Cat16 R2

Thermowells - Machined Barstock

T090 & T096 Series - ANSI Flange Style Shank For a tapered shank, change 090 to 094, or, 096 to 098

P = 1 1/4” nominal.

Element Length (A)

Insertion Length (U)

Shank Diameter (Q)

Bore Inches

Part Number

T09000-MC-RFxxxx-02 T09000-MC-RFxxxx-04 T09000-MC-RFxxxx-07 T09000-MC-RFxxxx-10 T09000-MC-RFxxxx-12 T09000-MC-RFxxxx-16 T09000-MC-RFxxxx-22 T09600-MC-RFxxxx-02 T09600-MC-RFxxxx-04 T09600-MC-RFxxxx-07 T09600-MC-RFxxxx-10 T09600-MC-RFxxxx-12 T09600-MC-RFxxxx-16 T09600-MC-RFxxxx-22

4” 6” 9”

2” 4” 7”

.260

12” 15” 18” 24”

10” 13” 16” 22”

3/4”

Raised Face RF

T090

4” 6” 9”

2” 4” 7”

T096

.385

12” 15” 18” 24”

10” 13” 16” 22”

7/8”

MC = Material Code from Table. RFxxxx = Raised Face actual Diameter + Pounds / inch flange size. For inserting a code see instructions and table on page 31

P

T100 & T160 Series - Van Stone Style

For a tapered shank, change 100 to 104, or, 106 to 108

Nominal Diameter (P)

Element Length (A)

Insertion Length (U)

Shank Diameter (Q)

Raised Face (R)

Bore Inches

Part Number

T010016-MC-FGxxx-02 T010016-MC-FGxxx-04 T010016-MC-FGxxx-07 T010016-MC-FGxxx-10 T010016-MC-FGxxx-13 T010016-MC-FGxxx-16 T010016-MC-FGxxx-22 T010024-MC-FGxxx-02 T010024-MC-FGxxx-04 T010024-MC-FGxxx-07 T010024-MC-FGxxx-10 T010024-MC-FGxxx-13 T010024-MC-FGxxx-16 T010024-MC-FGxxx-22 T010616-MC-FGxxx-02 T010616-MC-FGxxx-04 T010616-MC-FGxxx-07 T010616-MC-FGxxx-10 T010616-MC-FGxxx-13 T010616-MC-FGxxx-16 T010616-MC-FGxxx-22 T010624-MC-FGxxx-02 T010624-MC-FGxxx-04 T010624-MC-FGxxx-07 T010624-MC-FGxxx-10 T010624-MC-FGxxx-13 T010624-MC-FGxxx-16 T010624-MC-FGxxx-22

4” 6” 9”

2” 4” 7”

1” NPT

2” Dia.

.260

12” 15” 18” 24”

10” 13” 16” 22”

3/4”

(1.315” Dia. actual)

R Dia.

4” 6” 9”

2” 4” 7”

1 1/2” NPT

2 1/2” Dia.

.260

12” 15” 18” 24”

10” 13” 16” 22”

3/4”

(1.900” Dia. actual)

T100

T160

4” 6” 9”

2” 4” 7”

1” NPT

2” Dia.

.385

12” 15” 18” 24”

10” 13” 16” 22”

7/8”

(1.315” Dia. actual)

MC = Material Code from Table. FS = Flange is not shown in picture and drawing above. For adding a flange and code, see instructions and table on page 31 If no FS flange then leave “ FGxxx ” out of the part number .260 Bore is for a 1/4” diameter element. .385 Bore is for a 3/8” diameter element.

4” 6” 9”

2” 4” 7”

1 1/2” NPT

2 1/2” Dia.

.385

12” 15” 18” 24”

10” 13” 16” 22”

7/8”

(1.900” Dia. actual)

Page 100

Phone: 617.527.4385 Fax: 617.964.3746 Email: sales@asrichards.com